READY FOR PROJECT START

phyBOARD®-Nunki
Thermal imaging kit

phyCAM-P / phyCAM-S + development kit with NXP i.MX 6 and thermal imaging camera

  • Development platform for cost-effective thermal imaging systems
  • 32 x 32 pixel thermal imaging camera module
  • NXP i.MX 6 quad core processor
  • 2 independent camera inputs - expansion by visual camera possible
  • CAN interface, Ethernet, SD card, 2x USB
  • Linux-based system - easy development of complex applications
  • OpenCV and GStreamer im BSP, Halcon-Ready Image
  • Pre-installed softwareBSP with integrated camera driver
  • Fast into series production: work with series components as early as the development phase

Kit contents:

  • phyBOARD Nunki i.MX 6
    (ARM Cortex-A9, 4x 1 GHz, 1 GB DDR, 1 GB Flash)
  • VM-050-050-0 (thermal camera 32 x 32)
  • Lens, germanium, f = 5mm (permanently installed)
  • HDMI and LVDS connector, color, with touch
  • Embedded Linux BSP
  • Pre-installed software image with pre-installed camera driver
  • USB cable (serial communication), camera cable 30 cm, power supply unit
  • software image with Halcon HPeek demo version as SD card image (download access)
  • LiveUSB stick with drivers, demos, examples
  • Extensive documentation, reference circuit diagrams
  • Commissioning guarantee

Description:

Thermal imaging cameras open up completely new information. With the extremely inexpensive thermography modules VM-050 / VM-051, these advantages can also be used in your own series products. The integrated preprocessing of the modules provides fully corrected, directly usable temperature data as image information. These can be easily evaluated like a normal camera image.
The phyBOARD Nunki has two camera interfaces so that an additional camera - e.g. in the visible wavelength range - can be connected. By overlaying the images, additional information can be obtained and the subjective resolution of a display can be increased.

Develop your application with the phyBOARD Nunki with the variously supported NXP i.MX 6 processor under Linux.
The kit is based on components suitable for series production that can be transferred directly to series production. This minimizes the development effort. The phyBOARD itself has also been developed for series production and can be used as a single board computer. Phytec offers a cost-effective development service for any adjustments.

The kit includes the thermal imaging camera module VM-050-050-0. This camera delivers a corrected thermal image of 32 x 32 pixels with 8,9 fps. The value of each pixel represents the temperature of the object point. The thermal imaging module is supplied with a fully assembled, high-quality germanium optic (opening angle 33 °). If required, our sales team will be happy to put the kit together with other models from the VM-050 / VM-051 series.

The board can be operated with 12-24 V and, in addition to other interfaces, has an Ethernet and two USB 2.0 interfaces as well as a CAN interface. The phyCORE i.MX 6 module is plugged in interchangeably. Commissioning can take place via a directly connected HDMI monitor.

The kit includes the LinuxBSP included in series quality. Drivers for the camera and interfaces as well as the image processing libraries OpenCV and GStreamer are in the BSP integrated. This is for a direct start BSP already installed ready for use.

Module phyCORE-i.MX 6
SOM Mounting Connector insertion
Processor i.MX 6Quad
Architecture ARM Cortex-A9
Frequency 4x 1 GHz
NAND Flash 1 GB
SPI NOR Flash 16 MB
DDR3 RAM 1 GB
EEPROM 4 kB
Ethernet 1x 10/100/1000 Mbit/s
USB 1x Host, 1x OTG
Serial via microUSB
Digital I/O via Expansion Connector
PCle 1x miniPCIe
Mass Memory microSD Card Slot, SATA
Display HDMI, LVDS, Parallel
Audio via Expansion
Camera Interface 2x, both with phyCAM-P or phyCAM-S+ or one with MIPI CSI-2
Camera Thermal camera 32x32 VM-050-050-0
Lens f=5.0 33° (Germanium)
Expansion Bus USB, UMI, Power Control Signals (Reset, Power-Good...)
JTAG on Connector
User Control Elements Reset Button
Boot Source SD Card, NAND, eMMC, SATA, USB Host
RTC RTC with Gold Cap Backup
Power Supply 12-24 V
Connectors Samtec 0.5 mm pitch (280 pins)
Dimensions 150 mm x 75 mm
Temperature range -25°C to +85°C
Betriebssystem Linux 4.19.100
Distribution Yocto 2.7.4 (Warrior)

phyBOARD-Nunki Thermal Kit

Yocto-Linux Mainline-Kernel
Release Name Release Version Release Notes BSP Manual Yocto Manual Development Env. Guide Miscellaneous

Didn't find an answer? Just ask your question in Live Chat

If you have any questions, please contact our technical sales department directly: +49 (0) 6131 9221-32

symbol online shop.svg

phyBOARD Nunki
Thermal imaging kit


Item No.: KPB-02301-Video-L03

Available variants:

420.00  plus VAT.

Due to the current component situation, you will receive the delivery date in the order confirmation

Quantity:

Add-on item number Price Order
Display kit: AV adapter, 7 '' EDT display with capacitive touchKPEB-AV-02125.00 plus VAT.

Education + Training _ Use our know-how for your product development

With the know-how transfer from our experts to your developers, you will reach your goal faster!

 

Participants in our training courses receive a solid knowledge of professional hardware and software development.

Online seminars _ Helpful embedded knowledge explained in a nutshell in short video sessions

In informative online seminars with our experts and partners, we will inform you about exciting topics from the embedded industry.

You will get a free insight into new hardware and software solutions and learn more about special offers.

Do you have questions about an embedded topic? Arrange an online meeting now!

 

Within 30 minutes you will learn new solutions for your project.
You can also secure exclusive offers after your conversation.